Free fire escape plan · auto body shops
A body shop puts a paint booth, a mixing room full of coatings and solvents, sanding dust and a welder under one roof. Sketch the bays, the booth and the mixing room, or photograph the floor plan you already have, and the free draft puts routes, exits and a meeting point on it. The booth, prep-deck and frame-rack sections below cover what a drawing can’t show.
A planning draft, not a booth inspection or a permit. OSHA’s spray finishing rules and your local fire code both apply, so walk the shop before you post it.
Spray booth and mixing room
The booth and the mixing room hold the most flammable material in the shop, and people work inside both with the doors shut. Each one needs a door people can open on their own, leading away from the paint.
The fire code sends spray booth exits to its general means-of-egress chapter, and lets the doors of premanufactured booths be as small as 30 inches wide by 80 inches high (IFC 2021 section 2404.3.3.4). On your draft, the route from inside the booth should end at its personnel door.
An exit route door has to swing out in the direction of travel if the room holds more than 50 people or is a high hazard area (29 CFR 1910.36(e)(2)). Ask whether that describes your mixing room, and check which way its door opens.
Flammable liquids near the spraying are kept to the minimum the work needs, ordinarily no more than one day’s or one shift’s supply, with bulk stock in a detached building or a cut-off room (29 CFR 1910.107(e)(2)). A smaller stock in the mixing room also keeps its door and aisle clear.
Keep at least 3 feet clear on every side of the booth, free of storage and combustible construction (IFC 2021 section 2404.3.3.5). The fire code allows less space beside a wall rated at least 1 hour or a noncombustible exterior wall, as long as the booth can still be cleaned and maintained. Ask your fire marshal which edition and exceptions apply to your booth.
Prep decks, dust and filters
Prep work leaves residue on every surface, and paint waste builds up through the shift. These rules decide how often it leaves the building, which keeps it out of the aisles your routes use.
| In the shop | What the rule says | Source |
|---|---|---|
| Overspray on booth walls, floors and ducts | Spraying areas are kept free of combustible residue, cleaned daily if necessary, with nonsparking scrapers. | 1910.107(g)(2) |
| Rags and waste soaked with paint or solvent | Approved metal waste cans hold them, emptied at least once daily or at the end of each shift. | 1910.107(g)(3) |
| Oily rags from the rest of the shop | Materials that can ignite on their own go in a listed disposal container that’s emptied daily. | IFC 2021 304.3.1 |
| Used filters, drums and parts carts | Exit routes stay free of materials and equipment, even for a short time. | 1910.37(a)(3) |
| Boxes and masking paper beside the booth | At least 3 feet on all sides of the booth stays free of storage. | IFC 2021 2404.3.3.5 |
Shading the 3-foot space around the booth on your sketch makes it easier to spot filter boxes and carts that have crept into it.
Assembly point · the generator
Use a floor plan, a PDF, a phone photo or a sketch of one floor, with the booth, mixing room and prep decks labeled. The draft adds routes, exits, safety symbols and a meeting point. Then check each route in the shop: the booth and mixing room should lead away from the paint, and nothing should squeeze past the frame rack.
Drag & drop your floor plan here
or
PNG, JPG, HEIC, TIFF, BMP, SVG, AVIF, WebP, PDF, DOC, DOCX, PPT, PPTX, XLS, XLSX, ODT, ODP, ODS, DXF, DWG - Hand-drawn sketches work too!
No floor plan handy? Try the included floor plan with real AI generation — no upload needed. This may take a minute or longer.
Yes — you can generate your first OSHA-aligned evacuation map draft completely free. Just upload a floor plan and our AI drafts a professional map in about 30 seconds. No credit card required.
Our AI drafts maps that follow OSHA 29 CFR 1910.36–37 and NFPA 101 Life Safety Code standards. Every map includes clearly marked exits, fire extinguisher locations, assembly points, and directional evacuation arrows. Supervisor review is required before posting to your facility.
We accept PNG, JPG, GIF, WebP, BMP, TIFF, AVIF, HEIC, SVG, PDF, DOC/DOCX, PPT/PPTX, XLS/XLSX, ODT, ODP, ODS, DXF, and DWG floor plans. Office and CAD files are converted securely before processing; PDF uploads let you choose the source page.
Most maps are generated in 20–40 seconds. Complex multi-floor plans may take slightly longer. You see the preview instantly — create a free account (no credit card) to download the file.
Yes — every generated map opens in a free drag-and-drop editor where you can move, resize, and recolor exit signs, routes, and equipment icons. Enterprise features like multi-floor support and branded maps are available on paid plans.
Yes. All uploads are encrypted in transit (TLS 1.3) and processed in secure cloud environments. We do not share your floor plans with third parties.
Each result is a draft. Walk the routes past the booth and the frame rack before you post it, and follow your local fire code.
Before and after
The plain plan shows the booth, the mixing room, two prep decks and the frame machine. The draft adds routes that lead away from the booth, exits and extinguishers, and a meeting point in the customer lot.
What the draft adds to a body shop plan
Welding and fresh paint
Collision repair means welding and cutting in the same building as paint. Where you set up the welder decides whether a spark can reach the booth, a freshly painted panel or a cart of solvent.
No open flame or spark-producing equipment goes in any spraying area or within 20 feet of it, unless a partition separates them (29 CFR 1910.107(c)(2)). Set the welding spot beyond that distance and mark it on your sketch.
Before welding, movable fire hazards nearby go to a safe place. If they can’t be moved, guards confine the heat, sparks and slag, and if neither is possible, there’s no welding (29 CFR 1910.252(a)(1)). Think of masking paper, removed trim and seat covers near the frame rack.
A fire watch is required when combustibles sit closer than 35 feet to the work, among other cases, and it lasts at least half an hour after welding ends (1910.252(a)(2)(iii)(A) and (B)). Name the person who keeps watch before the welder starts.
Clothing worn by spray employees isn’t left in the building overnight unless it’s in metal lockers (29 CFR 1910.107(g)(4)). On the map, keep the lockers out of the aisle a route uses.
Frame racks and waiting cars
A car on the frame rack with its chains out, another waiting for the booth and a cart of parts can turn a wide shop into a narrow one. These rules set the minimum your routes need.
If a waiting car ends up in a route, move the car rather than redrawing the route around it. The posted map should show the way out on an ordinary busy day.
Keep planning
Guides for trades that share a body shop’s booths, welders and metal dust, plus pages for the written plan and the posted signs.
Questions
Yes. Upload a floor plan, a phone photo or a sketch of the shop and see a watermarked preview without signing up. A free account, no credit card needed, includes 5 free floor-plan uploads per month, with up to 5 regenerations per upload and the editor. Exports stay marked as drafts until you finish the posting review.
Map a route from inside the booth to its personnel door and on to an exit. The 2021 International Fire Code sends spray booth exits to its means-of-egress chapter and allows doors on premanufactured booths as small as 30 by 80 inches (section 2404.3.3.4). Your city may use a different edition.
The 2021 International Fire Code asks for at least 3 feet on all sides, free of storage and combustible construction, with exceptions for walls rated at least 1 hour and noncombustible exterior walls (section 2404.3.3.5). Ask your fire marshal which edition and exceptions apply.
OSHA’s spray finishing rule keeps open flames and spark-producing equipment out of any spraying area and more than 20 feet from it, unless a partition separates them (29 CFR 1910.107(c)(2)). Mark the welding spot on your sketch so the distance is easy to check.
Paint-soaked rags and waste go in approved metal waste cans, emptied at least once a day or at the end of each shift (29 CFR 1910.107(g)(3)). Wherever the cans and used filters wait, keep them out of the exit routes (29 CFR 1910.37(a)(3)).
Yes. Draw the outside walls, every door, the booth, the mixing room and the prep decks, and write their names clearly. A phone photo of the sketch works if it’s taken straight on in good light.
Illustrations on this page use fictional layouts made for this page. They are not customer plans or live generator results.
Upload the shop’s plan or a sketch and see the booth routes on a free draft.
Draft my body shop plan
